Resilio-Sync (formerly BitTorrent Sync) uses the BitTorrent protocol to sync files and folders between all of your devices. There are both free and paid versions – this container supports both. There is an official sync image, but this one supports user mapping to simplify permissions for volumes. In this step by step guide I will show you how to install Resilio-Sync on your Synology NAS with Docker & Portainer.
STEP 1
Please Support My work by Making a Donation.
STEP 2
Install Portainer using my step by step guide. If you already have Portainer installed on your Synology NAS, skip this STEP. Attention: Make sure you have installed the latest Portainer version.
STEP 3
Make sure you have a synology.me Wildcard Certificate. Follow my guide to get a Wildcard Certificate. If you already have a synology.me Wildcard certificate, skip this STEP.
STEP 4
Go to Control Panel / Login Portal / Advanced Tab / click Reverse Proxy. Follow the instructions in the image below.
STEP 5
Now click the “Create” button. Follow the instructions in the image below.
STEP 6
After you click the Create button, the window below will open. Follow the instructions in the image below.
On the General area, set the Reverse Proxy Name description: type in Resilio-Sync. After that, add the following instructions:
Source:
Protocol: HTTPS
Hostname: resilio.yourname.synology.me
Port: 443
Check Enable HSTS
Destination:
Protocol: HTTP
Hostname: localhost
Port: 7888
STEP 7
On the Reverse Proxy Rules click the Custom Header tab. Click Create and then, from the drop-down menu, click WebSocket. After you click on WebSocket, two Header Names and two Values will be automatically added. Click Save. Follow the instructions in the image below.
STEP 8
Go to Control Panel / Network / Connectivity tab/ Check Enable HTTP/2 then click Apply. Follow the instructions in the image below.
STEP 9
Go to Control Panel / Security / Advanced tab/ Check Enable HTTP Compression then click Apply. Follow the instructions in the image below.
STEP 10
Go to File Station and open the docker folder. Inside the docker folder, create one new folder and name it resilio-sync. Follow the instructions in the image below.
Note: Be careful to enter only lowercase, not uppercase letters.
STEP 11
Now create three new folders inside the resilio-sync folder that you created at STEP 10 and name them config, data, downloads. Follow the instructions in the image below.
Note: Be careful to enter only lowercase, not uppercase letters.
STEP 12
Log into Portainer using your username and password. On the left sidebar in Portainer, click on Stacks then + Add stack. Follow the instructions in the image below.
STEP 13
In the Name field type in resilio. Follow the instructions in the image below.
version: "3.9"
services:
resilio-sync:
image: ghcr.io/linuxserver/resilio-sync:latest
container_name: Resilio-Sync
hostname: resilio-sync
mem_limit: 4g
cpu_shares: 768
security_opt:
- no-new-privileges:true
healthcheck:
test: curl -f http://localhost:8888/ || exit 1
ports:
- 7888:8888 # WebUI
- 55555:55555 # Sync Port
volumes:
- /volume1/docker/resilio-sync/config:/config:rw
- /volume1/docker/resilio-sync/downloads:/downloads:rw
- /volume1/docker/resilio-sync/data:/sync:rw
environment:
TZ: Europe/Bucharest
PUID: 1026
PGID: 100
restart: on-failure:5
Note: Before you paste the code above in the Web editor area below, change the value for TZ. (Select your current Time Zone from this list.)
Note: Before you paste the code above in the Web editor area below, change the value numbers for PUID and PGID with your own values. (Follow my step by step guide on how to do this.)
STEP 14
Scroll down on the page until you see a button named Deploy the stack. Click on it. Follow the instructions in the image below. The installation process can take up to a few minutes. It will depend on your Internet speed connection.
STEP 15
If everything goes right, you will see the following message at the top right of your screen: “Success Stack successfully deployed“.
STEP 16
Go back to STEP 1 or you will deal with karma 🙂
STEP 17
Now open your browser and type in your HTTPS/SSL certificate like this https://resilio.yourname.synology.me that you have previously created at STEP 6. In my case it’s https://resilio.mariushosting.synology.me If everything goes right, you will see the Resilio-Sync login page. Type in your own Username and Password then click Continue. Follow the instructions in the image below.
STEP 18
Click Sync Home. Follow the instructions in the image below.
STEP 19
Choose a name to show when you send and receive folders. Check both user agreements, then click Get started. Follow the instructions in the image below.
STEP 20
Type in your own Username and Password that you have previously created at STEP 17 then click Sign In. Follow the instructions in the image below.
STEP 21
Your Resilio-Sync dashboard at a glance!
Enjoy Resilio-Sync!
If you encounter issues by using this container, make sure to check out the Common Docker issues article.
Note: Can I run Docker on my Synology NAS? See the supported models.
Note: Find out how to update the Resilio-Sync container with the latest image.
Note: How to Free Disk Space on Your NAS if You Run Docker.
Note: How to Schedule Start & Stop For Docker Containers.
Note: How to Activate Email Notifications.
Note: How to Add Access Control Profile on Your NAS.
Note: How to Change Docker Containers Restart Policy.
Note: How to Use Docker Containers With VPN.
Note: Convert Docker Run Into Docker Compose.
Note: How to Clean Docker.
Note: How to Clean Docker Automatically.
Note: Best Practices When Using Docker and DDNS.
Note: Some Docker Containers Need WebSocket.
Note: Find out the Best NAS Models For Docker.
Note: Activate Gmail SMTP For Docker Containers.
This post was updated on Monday / December 4th, 2023 at 12:57 AM